Solve your electric fence problem

Share

Issue Time: Jul 29,2022

Summary

Figuring out and solving the fault on the electrical fence can appear to be a frightening mission. But while there are loads of things that went wrong, systematically addressing them will help you find and accurate issues quick

^{Figuring out and solving the fault on the electrical fence can appear to be a frightening mission. But while there are loads of things that went wrong, systematically addressing them will help you find and accurate issues quick. Following the manual beneath, you'll entire a sequence of simple exams, beginning along with your fence strength deliver as a power supply. Remember the fact that fault finding is just a method of elimination, starting along with your energy supply (energy deliver) and then checking ground, underground cables, connections, and fence strains. But, you do need a digital voltmeter or fault finder to deal with a fault on the fence. Those will inform you the power degree of the electrical fence and in which there can be issues. For extremely small installations, a neon fence tester is enough. Observe this system until the barrier fails.}

^{Degree the voltage on the electrical fence line}

^{Check that your Energiser is working nicely}

^{Take a look at the grounding}

^{Test your digital fence connection}

^{Check your electric fence using a fault finder}

^{Take a look at your digital fence the usage of a digital voltmeter or neon fence tester}

^{Degree the electrical fence line}

^{Use a voltmeter to read from the fence line. For small decreases in ordinary degrees - say, 10-20% - then the problem is probably to be at your fence line. The large strength supply will operate at approximately 5000 volts and will stay so even underneath sizable load from plant life; Smaller generators will operate at 6-7000 volts, however these ranges will drop fast with any load or hassle on the fence.}

^{Check that your Energiser is running well}

^{Disconnect the floor and fence cables from the output terminals and then check the voltage with the aid of connecting a voltmeter to those terminals. (the output voltage varies from source to supply and may be determined inside the manual, but is commonly well above five,000 volts or 5kv.) Do not open the energy container. Transfer off the power supply when changing the cable.}

^{If it exceeds 5000 volts, hold to check the grounding}

^{If the voltage is underneath 5000 volts, please call us or your carrier agent. The fence booster itself may be faulty.}

^{If there's no voltage, take a look at the plug fuse on the power deliver and essential strength deliver. For battery suppliers, take a look at that the battery is completely charged and that the fence leads are not damaged or worn. If the energizer nevertheless doesn't paintings, please contact us.}

^{Test your grounding}

^{Poor grounding installation is frequently the purpose of low voltage in your electric powered fence. You could study about grounding in our grounding guide, or browse the short checklist below.}

^{Your ground bar must be made from galvanized steel and linked to the exciter by way of underground cables.}

^{The rod shall be ten metres from any other grounding tool, i.E. The ones used by the phone or power enterprise. Do now not use metallic water pipes or metal systems as soil.}

^{In widespread, one meter of soil is wanted for every joule of power, or 5 meters of grounding for a five-joule fence energizer. Your floor rods need to be as a minimum four metres aside.}

^{In case your grounding appears correct, take a look at it by using developing a whole brief circuit hundreds of meters away from the generator. Lay an iron bar at the twine to connect the fence line at once to the ground. Then location the voltmeter on the remaining floor bar in the line and take a look at whether or not there is a voltage between the ground bar and the earth.}

^{No readings under 500 volts - hold checking your fence connection.}

^{Any studying above 500 volts. Any recorded voltage represents a loss at the fence line. Add extra rods at four meter durations till the analyzing is below 500 volts.}

^{Check your electric powered fence connection}

^{Now you want to check the cables that join the electricity deliver to the fence. Disconnect the cable from the fence, then test the voltage studying on the end of the cable.}

^{In case your voltage analyzing suits the reading you acquired in advance at the energizer, the fault is on the fence line. Maintain to check your fence line the usage of a fault finder or check your fence line using a virtual voltmeter or neon fence tester.}

^{If the studying is a long way beneath the actuator, the cable is broken, or the cable is not big enough to transmit electricity.}

^{Use Fault Finder to test you}

^{While electricity escapes to the floor, your electric powered fence will short out. This will be due to damaged underground cables, damaged wires or insulators, free connections, or some thing touching the wires (along with an excessive amount of vegetation). The fault finder permit you to find the source of the quick circuit through measuring the strength float from the fence exciter to the ground.}

^{Place it on any part of the fence line and flow it laterally to get precise contact. In a valid electronic fence without a brief circuit, the amperage reading on the home screen may be 0 due to the fact nothing is flowing out of the system. The voltage analyzing at the screen inside the higher proper nook have to be about 6000 volts. Any reading at the ampere scale shows a few form of fault with your fence. The more intense the fault, the higher the amperometric analyzing. You will additionally see an arrow pointing within the direction of the fault.}

^{Follow the arrow till the analyzing drops or disappears - this suggests that you are just out of hassle. In a multi-wire electric fence, you want to test each twine in turn, beginning at the pinnacle. If there are multiple faults, it is able to be less difficult to isolate sections of the fence with a cutoff switch, so you can remove one phase at a time.}

^{If the electric fence splits at a Y or T junction, read each line and follow the line with the best analyzing. The equal applies in case your fence has an up and down hyperlink at the start of each section.}

^{If you have an electric fence or floor loop system with live twine and ground wire, and the studying on the floor cord is high, you must assume that the stay wire is touching the ground twine, causing a entire short circuit.}

^{Pay special attention to gateways and underground cable connectors.}

^{Use a virtual voltmeter or neon fence tester to test you}

^{Whilst energy escapes to the floor, your electric powered fence will quick out. This will be as a result of damaged underground cables, broken wires or insulators, loose connections, or some thing touching the fence (as an instance, too much vegetation). A digital voltmeter assist you to find the supply of the short circuit with the aid of measuring the voltage in the fence line. You could use it, too, even though it is less correct.}

^{Attach it to the fence line, flow laterally to get top contact, and area the probe at the floor. You will see a readout at the screen - on a terrific electric fence line, this must be over 6,000 volts.}

^{If the voltage is slightly beneath regular (for example, 5,000 volts), then you can enjoy minor glitches due to mild vegetation, as an example. But, if the studying is substantially decrease, there may be a chief fault.}

^{To look for this fault, flow along the fence line and take readings each 100 meters or so. Generally of thumb, the voltage will drop by about 100 volts every 100 meters as you head towards the fault, and then it's going to level off as you skip via the fault.}

^{If the fault is not apparent, you need to use a cutoff transfer to systematically isolate the place of the electric fence. As soon as you've got observed the problem location, you could need to isolate the person wires to identify the problem.}